Epoxy Flooring Installation in Richmond that lasts for years
Epoxy Flooring Installation in Richmond gives you a seamless, hard-wearing surface that shrugs off hot tires, road salt and dropped tools. We handle garages, basements, workshops and commercial bays across Richmond, British Columbia (BC), from concrete grinding right through to the final topcoat. If your slab is cracked, dusty or stained, we prep it properly and coat it once, so it stays put.
Service overview
What Epoxy Flooring Installation in Richmond involves
Epoxy Flooring Installation in Richmond is the process of grinding a concrete slab flat and clean, repairing cracks, then rolling on a resin and hardener system that cures into a single seamless surface. We start with a moisture meter reading and a diamond grinding pass to open the concrete pores, because epoxy needs a rough, dry, dust-free profile to bond. Then we fill cracks with concrete crack filler, prime the slab, and build up coats of epoxy resin until the floor is thick enough to handle traffic, chemicals and hot tires without peeling. Most Richmond homeowners call us because their garage floor is a mess of oil stains, spider cracks and grey dust that tracks into the house. Others run workshops, restaurants or retail bays and need a floor that wipes clean at the end of the day. We also get plenty of calls from people searching for epoxy floor installation Richmond near me after a cheap DIY kit bubbled or lifted within a year. Proper prep is the difference, and that is the part most kits skip.
! Problems we solve
Peeling and bubbling epoxy from a previous DIY kit
Once moisture gets under a failed coating, it spreads. Sections lift, water pools in the gaps, and the whole floor starts coming up in sheets within a season or two.
Hot tire pickup lifting the coating in the garage
Tires park hot and cool against the floor, and cheap coatings soften and stick to the rubber. You end up with bare patches under each wheel and a floor that looks worse than the concrete did.
Cracked, dusty concrete that will not hold a coating
Cracks move with the slab, and dust on the surface stops epoxy from bonding. Coating over either one guarantees a failure, and you are back to square one within a year.
Scope of work
What our epoxy flooring installation includes
Every quote covers the full job from prep to cleanup, so there is no surprise line item halfway through. Here is what comes standard on a Richmond Elite Epoxy Flooring installation, and what we price separately if your slab needs it.
-
01
Full surface preparation
We grind or shot blast the entire slab to open the concrete pores and remove contaminants, old coatings and failing patches. This is the step that decides whether the epoxy bonds or peels. It is included on every job, never sold as an upgrade.
-
02
Crack and patch repair
Structural cracks get cut open, cleaned and filled with concrete crack filler, then ground flush with the surrounding slab. Minor dips and spalls are patched before coating. Repairing first stops defects from telegraphing through the finished floor.
-
03
Base coat and broadcast
We roll a primer matched to your slab's moisture reading, then apply the epoxy base coat and broadcast flake or quartz aggregate while it is wet. This gives the floor its colour, depth and texture. Material quantities are calculated per square foot.
-
04
Topcoat and final cleanup
A polyaspartic or clear epoxy topcoat seals the broadcast and adds abrasion and UV resistance. We scrape excess flake, tape off edges, and clean the site before we leave. You get a walkthrough, a care sheet and your written workmanship warranty.
Why homeowners and businesses choose epoxy
A coated slab changes how a space works. Here is what our Richmond customers notice most after we finish, from easier cleaning to floors that survive a Canadian winter of road salt and wet boots.
Get a free quoteTools and methods we use on every job
Concrete grinder with diamond grinding wheel
Opens the concrete pores and removes contaminants, old coatings and surface laitance. This is the tool that creates the profile epoxy needs to bond. We run different grits depending on the slab condition and the coating system going on top.
Shot blaster
Used on larger commercial and industrial slabs where grinding would be too slow. It strips the surface down to clean concrete in a single pass and leaves a uniform profile. Common on warehouse and production floor jobs in Riverport.
Moisture meter
Reads moisture vapor transmission through the slab before we quote. If the reading is high, we specify a moisture barrier instead of a standard primer. Skipping this test is why so many coatings bubble and delaminate.
Epoxy mixing paddle and squeegee
The mixing paddle blends epoxy resin and epoxy hardener to an even consistency, which matters for cure strength. The squeegee spreads the base coat evenly across the slab before we back-roll it. Both are basic tools, used properly.
Local execution
Richmond sits at sea level with a wet coastal climate, and that shapes how we install epoxy here. Slabs in Steveston, Terra Nova and Hamilton often sit close to the water table, so moisture vapor transmission is a real concern and we test every floor before quoting. Winter humidity slows cure times, so we schedule coats with extra drying windows between October and March rather than rushing them. Older post-war homes in Shellmont and Burkeville often have thinner, more cracked slabs that need extra crack repair before coating, while new builds in McLennan North and West Cambie usually have cleaner concrete that preps faster. We work to WorkSafeBC rules on every site, and we keep dust contained with plastic sheeting so the rest of your home stays livable during the job. If you need same-day epoxy flooring installation Richmond homeowners can count on for a small repair, call early and we will fit you in where the schedule allows.
How epoxy flooring installation runs in Richmond
- • Steveston
- • Terra Nova
- • East Richmond
- • Brighouse
Recent work
Same-day service when your floor needs it
When a floor fails, we answer the phone
Coating failures do not wait for a convenient week. If your garage floor is lifting, a commercial kitchen floor has delaminated before an inspection, or a spill has damaged a workshop surface, call us and we will get someone out to look at it. We keep a stocked truck with primer, epoxy resin, hardener, flake and patching material, so most small repairs can be assessed and quoted on the first visit. For larger jobs we schedule a full crew, usually two to three installers, and block out the days needed to grind, repair and recoat. Typical response for a site visit in Richmond is within 24 to 48 hours, and we can often fit urgent commercial work in sooner. Reach out any time and we will tell you honestly what the floor needs.
How our epoxy installation process runs
On-site assessment
We walk the slab with you, take moisture meter readings and check for cracks, delamination and old coatings. You get a clear scope and a fixed price the same day. This visit usually takes 30 to 45 minutes, and it tells us whether the floor needs grinding, shot blasting or a moisture barrier.
Surface preparation
Prep is 60 percent of the job. We run a concrete grinder with a diamond grinding wheel across the whole slab to open the pores and remove contaminants. Cracks get cut out and filled, and any loose or peeling coating comes off before we go further. This stage takes a full day on most residential garages.
Crack repair and priming
We fill structural cracks with concrete crack filler and grind the patches flush. Then we roll on a primer matched to your slab's moisture reading. Skipping this step is why so many DIY floors bubble within a season, so we never rush it.
What epoxy flooring installation costs
Pricing depends on square footage, slab condition and the system you choose, so we quote after seeing the floor rather than over the phone. Typical 2026 pricing in Richmond runs from about $3 to $8 per square foot for a full installation, with most residential garages landing between $1,800 and $4,500. Flake and quartz finishes cost more than solid colour because of the extra material and labour. Crack repair, moisture barriers and old coating removal add cost, but they are what keep the floor bonded. We give you a fixed number, and we hold it.
Square footage and layout
A larger slab takes more material and more crew hours, so the per-square-foot rate drops slightly as size goes up. Tight spaces with posts, drains or equipment to work around slow the crew down and add labour. We measure on site rather than estimating from a photo.
Slab condition and prep needed
Clean, sound concrete preps fast. Cracked, spalled or oil-soaked slabs need extra grinding, patching and sometimes shot blasting. If there is an old coating to remove, that adds a day. Prep is the biggest variable in any quote, and skipping it is what causes failures.
Coating system and finish
A solid colour base coat with a clear topcoat is the most economical option. Flake and quartz broadcasts add material and labour. Metallic finishes and chemical-resistant systems cost more because they need specialised products and a more careful application.
Credentials and reviews
Frequently asked questions
How much does epoxy flooring installation cost in Richmond BC?
Most residential garages in Richmond run $1,800 to $4,500 in 2026, and commercial floors price per square foot from about $3 to $8 depending on the system. Flake and quartz finishes sit higher than solid colour. Crack repair, moisture barriers and floor removal add cost. We give you a fixed number after the site visit, so you are not guessing.
How long does epoxy flooring installation take in Richmond?
A standard two-car garage takes two to three days from grinding to final topcoat, and you can park on it 48 to 72 hours after the last coat. Larger commercial floors run four to seven days. Cure time stretches in cool, damp weather, so we build that into the schedule rather than rushing the coats.
Do I need to move everything out for epoxy floor installation in Richmond?
Yes, the space needs to be completely empty before we start. We need clear access to grind the full slab and roll coats edge to edge. Most customers move items into the driveway or a borrowed trailer the night before. If you are stuck, ask us and we can usually recommend a local storage option nearby.
Who offers epoxy floor installation near me in Richmond British Columbia (BC)?
Richmond Elite Epoxy Flooring has been installing resin floors here since 2018, covering garages, basements, workshops, restaurants and warehouses across the city. We handle prep, crack repair, coating and cleanup with our own crew. Call and we will book a site visit, usually within a few days.
Related services
Garage Floor Epoxy Coating
The most common job we run. A garage floor epoxy coating gives you a hard, chemical-resistant surface that handles hot tires, road salt and oil drips. We build it with a flake broadcast and polyaspartic topcoat so it stays bonded through Richmond winters.
Basement Epoxy Flooring
Basements in Richmond often sit close to the water table, so moisture control matters. We test the slab first, then install a coating that seals the concrete and gives you a clean, dry floor for storage, a gym or a suite. Anti-slip additive is standard here.
Book your Epoxy Flooring Installation in Richmond
We quote most Richmond jobs within a day of the site visit, and we hold that price. Our work is backed by a written workmanship warranty, and we clean up before we leave. Call us or send a message and we will get your floor on the schedule.